Structural differences between Westron-A sharpeners and other analogues
In fact, the machine was designed for himself, that is to ensure the best results in our service center. Therefore, its structure turned out to be so successful that allows almost anyone, especially an inexperienced person quickly, with maximum comfort in the highest quality and carry sharpening saws.
Index, letters after reaching 10/25, 30/60, 80/100, 110/150, 160/200 indicates the width of the saw band, which machine can grind the concrete.
To ensure long-term quality sharpening PZSL all machine parts are made of high quality steel with precision CNC 10 microns . Exact backlash-free engines manufactured by spetszakzu in the defense industry . In machine installed reinforced bearings upgraded accuracy. Accurate assembly provided by qualified staff. In addition, each machine is placed on a 3-day test run . All this makes it possible to operate the machine for a long time with little or no backlash and with almost zero beats , thus allowing use on max resource cbn grinding wheel.
For clarity, we show these improvements
PZSL |
Machines |
1.Prefabrication - You put the machine and immediately start working.
|
Machine manufacturers require some initial |
2. Has a powerful gear type oil pump (1) allows you to work with almost any type of oil at low temperatures. |
Is very weak oil pump able to work well only in a certain type of oil and temperatures above 15 ° C. At lower temperatures, oil thickens slightly weak and pump it can no longer pump. Before you start, you must first special heaters heat the oil so that it becomes more fluid. |
3. After prolonged use no oil is burnt. |
Even when one saw sharpening oil is burnt badly, ie requires mandatory forced hood. If it does not turn very quickly on site sharpening the air is so dirty that it was impossible to breathe.
|
4. In turning always clearly visible oil flow is fed to the grinding disc.
|
During turning can not see whether supplied through |
5. To ensure constant quality oil purification stage is set filters: - large round strainer (1) is under the grinding wheel and collects in large metal fraction; - strong magnet (2) mounted near the hole in the tank overflowing oil pump collects small metal fractions; - U-shaped strainer (3) placed in front of the oil pump, designed for the collection of non-metal fractions (threads from rags, sawdust, resin, etc.)
|
Cost is only one magnet, which is not able to provide quality oil purification, since it does not fully collects metal fractions and skips all non-metallic fraction. These fractions while turning quickly clog the nozzle oil line, reducing or completely stopping the flow of oil to the grinding disc, which leads to poor sharpening saw teeth (burn) and a strong reduction of the disk resource. |
6. Oil on disk supplied through nozzles 6-Th (1). Even if the flow of oil hammered 1-2 on the disc enough. When clogged nozzles are cleaned it easy to place any type of fixture wires, and since they are made of relatively large diameter, the oil pressure kicks dirt out. If a strong system clogged nozzles side unscrew the screw (2) and all the dirt immediately knocked out directly, then twists the screw back. All cleaning takes less than 1 minute.
|
Oil the drive has just two or three jets, a very small diameter. When operating the machine system maslopodachi hammered very often. Since during turning the flow of oil is not visible in its absence teeth cauterize, disk resource decreases. To clean the oil line system requires dismantling, disconnecting injectors and cleaning them separately, with a stop of the machine for 15-30 min. |
7. All motors are designed for continuous operation around the clock.
|
Engines are designed only for 2-3 hours, and if strongly heated do not pause can burn. |
8. To avoid generating stress saw tooth pusher (1) is made rotatable and removable. additionally, the pusher moves the emphasis is not on the line, and the path to eleps.
|
Emphasis pusher attached and not removable. Relatively quickly it formed to develop not accurately apply a tooth grinding disc, which leads to poor sharpening saw teeth and reduce disk resource, as it starts to hit you on the front, then on the back side of the tooth. |
9. To prevent generation on the pillars, they are made rotatable blade (1).
|
Folding saw relatively fast production constitutes a fixed support and saw starts to be supplied under the grinding wheel jerks. Result as in claim 8. |
10. Feeder saw teeth is made so that when turning the oil practically sprayed.
|
Feeder saw teeth is made so that when turning oil strongly scatters in all directions. To protect requires special casing. |
11. For precise oil supply and eliminating it splashing the oil pump has a smooth adjustment (1).
|
No.
|
12. You can sharpen the saw all existing profiles and widths of up to 10m.
|
Greater restrictions on profiles, width and length of saws. |
13. Convenient local lighting. The kit includes a special spotlight.
|
No local lighting. Difficult to configure the correct grinding wheel infeed. Poor pierce visible faces. You can not see that the cutting edge bad sharpened. |
14. Price at 30% - 50% lower than the analogues moreover, that the machine has all the advantages listed above. |
|